I have an Ender 3 V2 (stock hot end and bed heater) and about half a meter of 12V LED strip. Is there any way I can hijack the power supply's output to use for these LEDs?
I am having weird artefacts. Inconsistent layers, small splotches that aren't the seam and a very ugly looking seam. All these happen in the same place on multiple prints.
My printer seems to be making a "lip" so to speak on the outside of the curve when doing slight overhangs such as on the front of the benchy. It then proceeds to build over the curve creating this "mouth" on the benchy. I printed it twice and it happened in the same place. Ender 3 V2 Klipper.
I know i missed a few updates, but I didn't think I'd have to download the whole internet...
We’re planning a driving trip around Switzerland, so I thought it would be handy to print out a map
How do I make layers consistent? If I enable minimum layer time, then smaller layers get slowed down causing inconsistencies because of the speed. If I disable that, then I get layers being printed over layers before that can be at varying temperatures, still cooling, so still inconsistent.
Where does Cura actually get that ETA time? I change speed massively but it remains the same. Acceleration matters ofc, at 3000mm/s acc, it takes 3mm to go to 150mm/s but, 100mm to go to 800mm/s according to ChatGPT but then again, Cura doesn't know my acc and it should change a bit more than 3%.
What can I do to improve soft wise? As you can see stringing is less as temp is decreased and "print quality" goes up, up to 180C. Should I try even lower temp and give it tad more flow to fix the under extruded sections (those of which also decrease as temp decreases)? PLA on Ender 3 V2 w/ Klipper.
Off to a good start
9950X3D has blown my mind
Need Help Installing Klipper on Ender 3 V2 with BLTouch & Waveshare Touchscreen
Bad leveling, filament?
Is the Soleyin ultra PLA a good brand? I hear it's basically a sub-brand of Creality. What's for sure is that it's the cheapest branded PLA you can get.
So, I am trying to raise the speed on my Ender 3 V2 using Klipper. However there appears to be a roadblock in Cura. If I set the speed in Cura to anything higher than ~60mm/s, the ETA doesn't change from the one on 60mm/s.
Do I need to re-make klipper and reflash it to my printer every time I change something in the config file like adding BL-touch? (Ender 3 V2)
Ender 3 V2 not extruding fast enough. Repost with additional video
If I'm installing Klipper or, more precisely, MainsailOS. Do I need to change the firmware on my 3d printer also? There's nothing on the Mainsail site when getting started about firmware for your printer.
I'm about to install Klipper on my Ender 3 V2. But, how do I know when it is starting to slow down on normal firmware because of it's CPU? Does it just run at a slower speed automatically or does quality degrade? It was doing 60mm/s at 60 but then on 80mm/s in Cura it now seems to be doing about ~10
Must be a good printer!
If I have octoklipper installed on my raspberry pi can I still run python code to use the GPIO pins?
So, how would I use these IRL540N MOSFETS I have to power a ~11 Watt heater wire on 12V power supply using a raspberry pi as the signal (5V)?
What speed can I expect from my ender 3 v2 using PLA?
I am not sure if you can see it or not in the screenshot, it seems to disappear when trying to use win+shift+s but, there is a very subtle line, about 1-2 pixels wide along the whole heigh of the right side of the viewing screen. That line seems to be opaque and is showing what's BEHIND the browser.
